MAS™ Material List

• Footing & Foundation Pad

  	MAS-570™	MAS-1300™
  Concrete (foundation/footing) – 4,000 PSI w/ 3/4 inch minus aggregate	10 cubic yards	22.1 cubic yards
  Concrete (slab/pad) – 4,000 PSI w/ 3/4 inch minus aggregate	8 cubic yards	17.8 cubic yards
  Rebar (foundation/footing) – #3 (0.375 inch)	506 linear feet	1,125 linear feet
  Rebar (slab/pad) – #3 (0.375 inch)	400 linear feet	888 linear feet
  MAS-HELIX™ (Average)	371 lbs	675 lbs

• Structure

  	MAS-570™	MAS-1300™
  Concrete (shotcrete) – 3/8 inch to 5/16 inch (11/32 inch ± 1/16 inch)	18 cubic yards	38 cubic yards
  Concrete (shotcrete) – 3/8 inch to 5/16 inch (11/32 inch ± 1/16 inch) with Optional Roof Eve System	2.1 cubic yards	2.1 cubic yards
  Concrete Admix water proofing (consult engineer)	consult with engineer	consult with engineer
  Rebar – #3 (0.375 inch)	1,702 linear feet	4,010 linear feet
  Rebar – #3 (0.375 inch) with Optional Roof Eve System	720 linear feet	720 linear feet
  MAS-HELIX™ (Average)	307 lbs	558 lbs
  MAS-HELIX™ with Optional Roof Eve System	31.5 lbs	31.5 lbs
  Rebar Wire Ties	90 pieces	200 pieces
  Rebar Chairs – 1-1/2 inch plastic	35 pieces	65 pieces

• Concrete Notes

  Actual weights on sand and aggregate may change based upon your concrete provider. The following are approximate weights only.

  (1) Cement Powder (per cubic yard), 4,000 PSI often times accomplished with a 6 bag mix: 540 lbs
  (2) Washed Concrete Sand (per cubic yard): 1345 lbs
  (3) Aggregate (per cubic yard): 2010 lbs
  (4) Admix water proofing: consult engineer as this may not be needed (typically sold by the gallon)
  (5) MAS-HELIX™ is a micro-rebar that is critical to the structural integrity of the MAS structures.  MAS does not offer a re-bar ONLY solution due to the inability to achieve consolidation through the dense re-bar spacing required without MAS-HELIX™.  In addition, it is not possible to achieve the sheer strength necessary within the 4″ thick concrete shell used in the MAS structures without MAS-HELIX™.  MAS-HELIX™ is less expensive than re-bar and eliminates a significant amount of labor associated with the installation of re-bar.  MAS Engineering, in conjunction with your local Engineer of Record, will provide an exact MAS-HELIX™ dosage and re-bar count when final analysis is completed on your project.  Such MAS-HELIX™ dosage and re-bar count will be reflected on the Building Plan Package supplied to the builder.

  The figures used in the above tables represent a good starting point for the purposes of calculating costs only.  Variations will be minimal.

  DO NOT USE ANY OF THE FIGURES IN THESE TABLES FOR CONSTRUCTION PURPOSES.

• OPTIONAL Insulation

  Insulation is OPTIONAL and is considered a 3rd party accessory.  A thickness of 3″ gives an R60 equivalent value.  The following table assumes 3″ of insulation will be used.  Many times 1″ or 2″ is sufficient for your environmental conditions.  If using 1″ then multiply the values shown by 1/3 (0.34).  If using 2″ then multiply the values shown by 2/3 (0.67).

  	MAS-570™ Board Feet	MAS-1300™ Board Feet
  2 LB Density Spray Foam	1,800	4,200
  2 LB Density Panel Foam	3,000	6,000

• Electrical Conduit (poured in concrete)

  	MAS-570™	MAS-1300™
  3/4 inch x 10 feet Schedule 40 Conduit	TBD	16 Pieces
  3/4 sweeping 90 degree angle	TBD	6 Pieces
  Single Gang 16.5 cubic inch hand box (Steal)	TBD	16 Pieces
  3/4 inch Male Terminal Adapter	TBD	16 Pieces
  3/4 inch Female Terminal Adapter	TBD	16 Pieces
  3/4 inch Lock Nut	TBD	32 Pieces
  BL Mounting Clip	TBD	16 Pieces

• Plumbing Trough (poured in concrete)

  Contact MAS for more information on plumbing trough designs

• Forms & Tooling

  Form Ordering & Pricing

• MAS™ Per Unit ADELS Fee (ADELS Fee)

  Each MAS™ system (unit) requires this fee to be paid. There are NO quantity discounts. The ADELS Fee covers the architecture, engineering,  design (system plans), technical & logistical support, Southern Utah University (SUU) royalty fee, and warranty. Certification of trade personnel and companies is NOT included in this ADELS Fee. MAS™. Through it’s educational partners, SUU and Applied Technologies Centers (ATC), offers minimal cost training classes in Southern Utah (USA). Travel costs, lodging and meals are the responsibility of the training class attendees. However, MAS™ has arranged for substantial local lodging and restaurant discounts for attendees. Please contact the MAS™ Licensing & Certification Division for more information on certification packages.

  	MAS-570™ USD ($)	MAS-1300™ USD ($)
  MAS™ ADELS Fee	$2,487.00	$4,983.00

Metric Unit Material List Coming Soon